| 1 | U-Boot 1.3.4-svn (Feb 6 2010 - 12:35:58) for SMDK6410 |
|---|
| 2 | |
|---|
| 3 | |
|---|
| 4 | CPU: S3C6410@666MHz |
|---|
| 5 | Fclk = 666MHz, Hclk = 133MHz, Pclk = 66MHz |
|---|
| 6 | Serial = CLKUART (ASYNC Mode) |
|---|
| 7 | Board: Elice |
|---|
| 8 | DRAM: 64 MB |
|---|
| 9 | Booting: by Power Key |
|---|
| 10 | Flash: 0 kB |
|---|
| 11 | MMC C0: 1961 MB (moviNAND) |
|---|
| 12 | MMC C1: 0 MB |
|---|
| 13 | Card Initialization failed at channel 1 |
|---|
| 14 | NAND: 0 MB (Flash Based BBT Enabled) |
|---|
| 15 | *** Warning - using default environment |
|---|
| 16 | |
|---|
| 17 | |
|---|
| 18 | [[[[[[[[[[ Booting from MOVI NAND Ver. 0.3.6 ]]]]]]]]]] |
|---|
| 19 | |
|---|
| 20 | In: serial |
|---|
| 21 | Out: serial |
|---|
| 22 | Err: serial |
|---|
| 23 | Net: No ethernet found |
|---|
| 24 | Hit any key to stop autoboot: 0 |
|---|
| 25 | Reading kernel from channel 0 completed |
|---|
| 26 | Boot with zImage |
|---|
| 27 | |
|---|
| 28 | Starting kernel ... |
|---|
| 29 | |
|---|
| 30 | Uncompressing Linux................................................................................... |
|---|
| 31 | Linux version 2.6.28.6 (root@jang) (gcc version 4.3.2 (GCC) ) #1086 PREEMPT Thu Mar 18 14:04:42 KST 20 |
|---|
| 32 | CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f |
|---|
| 33 | CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache |
|---|
| 34 | Machine: SMDK6410 |
|---|
| 35 | Memory policy: ECC disabled, Data cache writeback |
|---|
| 36 | CPU S3C6410 (id 0x36410101) |
|---|
| 37 | s3c6410_init_clocks: initialising clocks |
|---|
| 38 | Change freq level 8 range |
|---|
| 39 | S3C24XX Clocks, (c) 2004 Simtec Electronics |
|---|
| 40 | s3c6400_setup_clocks: clkdiv0 = 01043310 |
|---|
| 41 | s3c6400_setup_clocks: xtal is 12000000 |
|---|
| 42 | S3C64XX: PLL settings, A=666000000, M=533000000, E=24000000 |
|---|
| 43 | S3C64XX: HCLKx2=266500000, HCLK=133250000, PCLK=66625000 |
|---|
| 44 | mout_apll: source is fout_apll (1), rate is 666000000 |
|---|
| 45 | mout_epll: source is fout_epll (1), rate is 67738000 |
|---|
| 46 | mout_mpll: source is mpll (1), rate is 533000000 |
|---|
| 47 | mmc_bus: source is mout_epll (0), rate is 16934500 |
|---|
| 48 | mmc_bus: source is mout_epll (0), rate is 16934500 |
|---|
| 49 | mmc_bus: source is mout_epll (0), rate is 16934500 |
|---|
| 50 | usb-host-bus: source is mout_epll (0), rate is 67738000 |
|---|
| 51 | uclk1: source is mout_epll (0), rate is 67738000 |
|---|
| 52 | spi-bus: source is mout_epll (0), rate is 67738000 |
|---|
| 53 | spi-bus: source is mout_epll (0), rate is 67738000 |
|---|
| 54 | audio-bus0: source is mout_epll (0), rate is 67738000 |
|---|
| 55 | audio-bus1: source is mout_epll (0), rate is 67738000 |
|---|
| 56 | audio-bus2: source is mout_epll (0), rate is 67738000 |
|---|
| 57 | irda-bus: source is mout_epll (0), rate is 67738000 |
|---|
| 58 | Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 |
|---|
| 59 | Kernel command line: root=/dev/ram0 rw ramdisk=5120 initrd=0x50800000,5M console=ttySAC0,115200 init=M |
|---|
| 60 | PID hash table entries: 256 (order: 8, 1024 bytes) |
|---|
| 61 | Console: colour dummy device 80x30 |
|---|
| 62 | unknown clock source mout_epll |
|---|
| 63 | console [ttySAC0] enabled |
|---|
| 64 | Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) |
|---|
| 65 | Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) |
|---|
| 66 | Memory: 64MB = 64MB total |
|---|
| 67 | Memory: 56556KB available (2692K code, 364K data, 124K init) |
|---|
| 68 | SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 |
|---|
| 69 | Calibrating delay loop... 665.19 BogoMIPS (lpj=1662976) |
|---|
| 70 | Mount-cache hash table entries: 512 |
|---|
| 71 | CPU: Testing write buffer coherency: ok |
|---|
| 72 | net_namespace: 288 bytes |
|---|
| 73 | NET: Registered protocol family 16 |
|---|
| 74 | S3C6410 Power Management, (c) 2008 Samsung Electronics |
|---|
| 75 | S3C6410: Initialising architecture |
|---|
| 76 | S3C DMA-pl080 Controller Driver, (c) 2006-2007 Samsung Electronics |
|---|
| 77 | Total 32 DMA channels will be initialized. |
|---|
| 78 | NET: Registered protocol family 2 |
|---|
| 79 | IP route cache hash table entries: 1024 (order: 0, 4096 bytes) |
|---|
| 80 | TCP established hash table entries: 2048 (order: 2, 16384 bytes) |
|---|
| 81 | TCP bind hash table entries: 2048 (order: 1, 8192 bytes) |
|---|
| 82 | TCP: Hash tables configured (established 2048 bind 2048) |
|---|
| 83 | TCP reno registered |
|---|
| 84 | checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd |
|---|
| 85 | Freeing initrd memory: 5120K |
|---|
| 86 | S3C64XX ADC driver, (c) 2008 Samsung Electronics |
|---|
| 87 | NTFS driver 2.1.29 [Flags: R/O]. |
|---|
| 88 | io scheduler noop registered |
|---|
| 89 | io scheduler cfq registered (default) |
|---|
| 90 | elice_hw_board_version_init() |
|---|
| 91 | ========================= |
|---|
| 92 | [ebook Board] elice MP 2 |
|---|
| 93 | [kernel ver.] 2.6.28 |
|---|
| 94 | [dev ver.] 1.0.4.4 |
|---|
| 95 | [rel ver.] 0.0.0.0 |
|---|
| 96 | ========================= |
|---|
| 97 | Elisa Battery Driver Init Success |
|---|
| 98 | [Elisa] Installed iriver Dynamic Clock Change Driver |
|---|
| 99 | check GPIO, HRDY: 1 |
|---|
| 100 | s1d13521ifgpio: set_cmd_mode(): |
|---|
| 101 | [s1d13521if_print_disp_timings] disp_timings: vsize=600 vsync=4 vblen=4 velen=10 |
|---|
| 102 | [s1d13521if_print_disp_timings] disp_timings: hsize=800 hsync=10 hblen=4 helen=100 |
|---|
| 103 | [s1d13521fb_print_wfm_info] wfm: fvsn=1 luts=0 mc=3 trc=10 eb=0xff sb=0xfc wmta=68 |
|---|
| 104 | Console: switching to colour frame buffer device 75x50 |
|---|
| 105 | fb0: s1d13521 frame buffer device |
|---|
| 106 | Success registering ELISA GPIO device |
|---|
| 107 | s3c6400-uart.0: s3c2410_serial0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10 |
|---|
| 108 | s3c6400-uart.1: s3c2410_serial1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10 |
|---|
| 109 | brd: module loaded |
|---|
| 110 | loop: module loaded |
|---|
| 111 | s3c-udc : S3C HS USB OTG Device Driver, (c) 2008-2009 Samsung Electronics |
|---|
| 112 | s3c-udc : version 15 March 2009 (DMA Mode) |
|---|
| 113 | mice: PS/2 mouse device common for all mice |
|---|
| 114 | input: s3c-keypad as /class/input/input0 |
|---|
| 115 | s3c-keypad Initialized |
|---|
| 116 | S3C Keypad Driver |
|---|
| 117 | elice_powerkey_probe !!!!!!!!!!! |
|---|
| 118 | elice powerkey register success !!! |
|---|
| 119 | S3C24XX RTC, (c) 2004,2006 Simtec Electronics |
|---|
| 120 | s3c2410_rtc: tick irq 34, alarm irq 92 |
|---|
| 121 | s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling |
|---|
| 122 | s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0 |
|---|
| 123 | i2c /dev entries driver |
|---|
| 124 | s3c2440-i2c s3c2440-i2c.0: slave address 0x10 |
|---|
| 125 | s3c2440-i2c s3c2440-i2c.0: bus frequency set to 378 KHz |
|---|
| 126 | s3c2440-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter |
|---|
| 127 | sdhci: Secure Digital Host Controller Interface driver |
|---|
| 128 | sdhci: Copyright(c) Pierre Ossman |
|---|
| 129 | s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133250000 Hz) |
|---|
| 130 | s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133250000 Hz) |
|---|
| 131 | s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (16934500 Hz) |
|---|
| 132 | 2, 0 ++++++++++++++++++ |
|---|
| 133 | mmc_send_app_op_cond, 172 ******** |
|---|
| 134 | ################## Retry !!!! |
|---|
| 135 | ################################### |
|---|
| 136 | [[[[[[[[[[ mmc serial= 218c36a7 ]]]]]]]]] |
|---|
| 137 | ################################### |
|---|
| 138 | mmc0: new high speed MMC card at address 0001 |
|---|
| 139 | mmcblk0: mmc0:0001 M2G1DD 1.91 GiB |
|---|
| 140 | mmcblk0: p1 p2 p3 |
|---|
| 141 | mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA |
|---|
| 142 | s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133250000 Hz) |
|---|
| 143 | s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133250000 Hz) |
|---|
| 144 | s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (16934500 Hz) |
|---|
| 145 | 2, 0 ++++++++++++++++++ |
|---|
| 146 | mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA |
|---|
| 147 | mmc_send_app_op_cond, 172 ******** |
|---|
| 148 | 0, 2 ++++++++++++++++++ |
|---|
| 149 | Advanced Linux Sound Architecture Driver Version 1.0.18rc3. |
|---|
| 150 | ASoC version 0.13.2 |
|---|
| 151 | |
|---|
| 152 | |
|---|
| 153 | GPDPUD=0x 2aa : GPDCON=0x 33333 |
|---|
| 154 | |
|---|
| 155 | WM8731 Audio Codec 0.13playback: 1, capture : 1 |
|---|
| 156 | asoc: WM8731 <-> s3c6410-i2s mapping ok |
|---|
| 157 | Codec Power off ++++++++ |
|---|
| 158 | ALSA device list: |
|---|
| 159 | #0: smdk6410 (WM8731) |
|---|
| 160 | TCP cubic registered |
|---|
| 161 | VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5 |
|---|
| 162 | s3c2410-rtc s3c2410-rtc: setting system clock to 2009-09-09 13:49:33 UTC (1252504173) |
|---|
| 163 | Loading Ramdisk From mmcblk0p3 |
|---|
| 164 | RAMDISK: cramfs filesystem found at block 0 |
|---|
| 165 | RAMDISK: Loading 5004KiB [1 disk] into ram disk... done. |
|---|
| 166 | VFS: Mounted root (cramfs filesystem) readonly. |
|---|
| 167 | Freeing init memory: 124K |
|---|
| 168 | ##### /etc/init.d/rcS Start ##### |
|---|
| 169 | mdev: mknod ram1: Read-only file system |
|---|
| 170 | =================== |
|---|
| 171 | rootfs ver: 0.0.7.0 |
|---|
| 172 | =================== |
|---|
| 173 | ##### /dev/mmcblk0p2 ##### |
|---|
| 174 | e2fsck 1.39 (29-May-2006) |
|---|
| 175 | ext2fs_check_if_mount: No such file or directory while determining whether /dev/mmcblk0p2 is mounted. |
|---|
| 176 | /dev/mmcblk0p2: clean, 558/24576 files, 122029/195312 blocks |
|---|
| 177 | FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! |
|---|
| 178 | ##### Run script /mnt/MOVIEXT2/rc.elisa ##### |
|---|
| 179 | ##### Mounted MOVIFAT ##### |
|---|
| 180 | <kernel : dcc> write_proc_gointosleep(): proc_gotosleep value 7 |
|---|
| 181 | current priority = <0> |
|---|
| 182 | current priority = <-19> |
|---|
| 183 | UNIT2 mplayer Daemon Version 0.0.1 ............[OK] |
|---|
| 184 | AudioCodecDecProc_ThreadCreate() |
|---|
| 185 | pthread_join befor!! |
|---|
| 186 | pthread_join after!! |
|---|
| 187 | RecordCodecEncProc_ThreadCreate() |
|---|
| 188 | ------------- GEQ ENABLE = 1 -------------- |
|---|
| 189 | [xmp_geq_set_band] band = 0 |
|---|
| 190 | ioctl gpio_get same value+++ |
|---|
| 191 | set_earphone_on_off, 138 HP OFF |
|---|
| 192 | ioctl gpio_get same value+++ |
|---|
| 193 | set_speaker_on_off, 116 Speaker Off |
|---|
| 194 | /mnt/ramfs/audio_play unlink fail !!! |
|---|
| 195 | /mnt/ramfs/rec_on unlink fail !!! |
|---|
| 196 | pthread_join befor!! |
|---|
| 197 | pthread_join after!! |
|---|
| 198 | ========================= |
|---|
| 199 | [flow, ebook App ] |
|---|
| 200 | [dev ver.] 1.7.1.0 |
|---|
| 201 | [rel v<kernel : dcc> elisa_dcc_ioctl(): Flow event -> curr_mode 1 |
|---|
| 202 | er.] 1.7.1.0 |
|---|
| 203 | ========================= |
|---|
| 204 | [flow, main, clock] high state!! |
|---|
| 205 | $$$$$ setting.xml FILE_SIZE[379] $$$$$ |
|---|
| 206 | $$$$$ keylang.xml FILE_SIZE[286] $$$$$ |
|---|
| 207 | <kernel : dcc> write_proc_gointosleep(): proc_gotosleep value 7 |
|---|
| 208 | [flow,pal] Device TYPE[tethered] ID: HEX[218c36a7] -> DEC[0562837159] @@@@@ |
|---|
| 209 | [flow,pal] SALT:(3732130136) |
|---|
| 210 | [flow,pal] SALT(Base64)[16]:(MzczMjEzMDEzNg==) |
|---|
| 211 | [flow,pal] salt file is OK! |
|---|
| 212 | @@@@@ Serial Number [0562837159] @@@@@ |
|---|
| 213 | @@@@@ Serial Number Base64 Encode [MDU2MjgzNzE1OTM3MzIxMzAxMzY=] @@@@@ |
|---|
| 214 | [flow] make DRM folder hidden!! |
|---|
| 215 | sh-4.0# [flow] make DRM folder hidden!! |
|---|
| 216 | -> device_id [218c36a7] len[8] |
|---|
| 217 | @@@@@ Create xbas.dat |
|---|
| 218 | |
|---|
| 219 | [Information] |
|---|
| 220 | Product=reigncom_eb02 |
|---|
| 221 | SN=IriverEB218c36a7 |
|---|
| 222 | Firmware=1.1.1.0 |
|---|
| 223 | |
|---|
| 224 | rm: cannot remove '/mnt/MOVIFAT/timerec.dat': No such file or directory |
|---|
| 225 | rm: cannot remove '/mnt/MOVIFAT/synclog.dat': No such file or directory |
|---|
| 226 | @@@@@ Remove timerec.dat |
|---|
| 227 | [flow, pal] fd_battery: 3 |
|---|
| 228 | [flow, pal] battery type: 1 |
|---|
| 229 | [flow, main] pre battery: 1 |
|---|
| 230 | create_event_manager()++ |
|---|
| 231 | create_event_manager()-- |
|---|
| 232 | [flow, main] pre usb, no detect!! |
|---|
| 233 | [flow, main] pre usb, disconnect!! |
|---|
| 234 | [flow, main] pre sd, eject!! |
|---|
| 235 | key_fd = 4 |
|---|
| 236 | /mnt/MOVIEXT2/iriver/app/launcher open failed!! |
|---|
| 237 | [model name] |
|---|
| 238 | 1.71 |
|---|
| 239 | |
|---|
| 240 | [flow, internal] proc SD mount install success, id: 100 |
|---|
| 241 | [flow, internal] proc SD unmount install success, id: 101 |
|---|
| 242 | [flow, internal] proc USB mount install success, id: 102 |
|---|
| 243 | [flow, internal] proc battery mount install success, id: 103 |
|---|
| 244 | [flow, internal] on_hook_key Hooking success, id: 100 |
|---|
| 245 | usb_charging_on: 0 |
|---|
| 246 | [start ebook execute] start.feb, pid: 101 |
|---|
| 247 | START-CREATE WINDOW--- |
|---|
| 248 | <start>(msg)(0x00001001) |
|---|
| 249 | END-CREATE WINDOW----- |
|---|
| 250 | <start>(msg)(0x00001012) |
|---|
| 251 | <start>(msg)(0x00001005) |
|---|
| 252 | <start>(msg)(0x00001004) |
|---|
| 253 | <start>(msg)(0x00001003) |
|---|
| 254 | <start>(msg)(0x00001007) |
|---|
| 255 | <start>(msg)(0x00001008) |
|---|
| 256 | AppMngInit():MainMenu Count(10) |
|---|
| 257 | AppMngInit():SubApp Count(6) |
|---|
| 258 | AppMngInit():SubApp Count(1) |
|---|
| 259 | poewroff time value 15 |
|---|
| 260 | [Kernel] setted poweroff time to powerOffTime 50400@@@@@ Set TimeZone Index[9] Value[0] |
|---|
| 261 | <start>Can Not Found Dic File(/mnt/MOVIFAT/dicdata_ebook/diclist.dicbin) |
|---|
| 262 | <resume>No Resume file[/mnt/ramfs/com_dic.cfg] |
|---|
| 263 | <resume>I will make the Resume file |
|---|
| 264 | <resume>Close() READWRITE |
|---|
| 265 | <start>execute(1)(mybook.feb), |
|---|
| 266 | <start>executed pid=(102)<7>s3c_rtc_setpie: pie=0 |
|---|
| 267 | |
|---|
| 268 | <start, usb> proc USB mount install success, id: 104 |
|---|
| 269 | [start] on_hook_key Hooking success, id: 101 |
|---|
| 270 | [start] proc SD unmount install success, id: 105 |
|---|
| 271 | [flow, start] proc SD mount install success, id: 106 |
|---|
| 272 | [flow, start] proc battery mount install success, id: 107 |
|---|
| 273 | XmlMenuString: Find Menu > Max Menu Why??? |
|---|
| 274 | [flow, internal] Create File : /mnt/MOVIFAT/Story.sys |
|---|
| 275 | |
|---|
| 276 | |
|---|
| 277 | MyBook application Start!! <kernel : dcc> elisa_dcc_ioctl(): Flow event -> curr_mode 1 |
|---|
| 278 | |
|---|
| 279 | |
|---|
| 280 | [flow, main, clock] high state!! |
|---|
| 281 | XmlMenuString: Find Menu > Max Menu Why??? |
|---|
| 282 | XmlMenuString: Find Menu == Max Menu (STATUS_SAVE_DONE) |
|---|
| 283 | XmlMenuString: Find All Menu:(28) |
|---|
| 284 | XmlMenuString: Find Menu > Max Menu Why??? |
|---|
| 285 | XmlMenuString: Find Menu == Max Menu (STATUS_SAVE_DONE) |
|---|
| 286 | XmlMenuString: Find All Menu:(15) |
|---|
| 287 | <start>(msg)(0x00001006) |
|---|
| 288 | <start>(msg)(0x0000A120) |
|---|
| 289 | <start>START_APP response(win_id:0x002187E0)(mybook.feb) |
|---|
| 290 | <start>Find Main! |
|---|
| 291 | [mybook] proc battery mount install success, id: 108 |
|---|
| 292 | [mybook] proc SD mount install success, id: 109 |
|---|
| 293 | [mybook] on_hook_key Hooking success, id: 102 |
|---|
| 294 | XmlMenuString: Find Menu > Max Menu Why??? |
|---|
| 295 | <mybook>start_flow() - power on<kernel : dcc> elisa_dcc_ioctl(): Flow event -> curr_mode 1 |
|---|
| 296 | |
|---|
| 297 | [flow, main, clock] high state!! |
|---|
| 298 | <mybook>db start... |
|---|
| 299 | |
|---|
| 300 | |
|---|
| 301 | dbapp_fix_date_error, curr time: 4aa7b272 |
|---|
| 302 | Error data No:0 |
|---|
| 303 | |
|---|
| 304 | |
|---|
| 305 | <mybook>db start... |
|---|
| 306 | <mybook>VOLUME[(null)] PATH[(null)] TOTAL_SPACE[0] FREE_SPACE[0] |
|---|
| 307 | Booktotal:212 |
|---|
| 308 | [flow, main, clock] finish!!<kernel : dcc> elisa_dcc_ioctl(): Get DCC_UPDATE_FINISH !! |
|---|
| 309 | <kernel : dcc> elisa_dcc_ioctl(): Get DCC_UPDATE_FINISH !! |
|---|
| 310 | <kernel : dcc> elisa_dcc_ioctl(): Flow event -> curr_mode 1 |
|---|
| 311 | <kernel : dcc> elisa_dcc_ioctl(): Get DCC_UPDATE_FINISH !! |
|---|
| 312 | |
|---|
| 313 | [flow, main] end flow_process_event() |
|---|
| 314 | |
|---|
| 315 | [flow, main, clock] finish!! |
|---|
| 316 | [flow, main] start main while(power_on)!! |
|---|
| 317 | [flow, main] sleep, wake up!!! |
|---|
| 318 | [flow, main, clock] high state!! |
|---|
| 319 | [mybook] on_battery_mount!, p1: -2, p2: 0 |
|---|
| 320 | ---------------> [main] PAL_BATTERY_SLEEP_OFF |
|---|
| 321 | [flow, internal] on_battery_mount!, p1: -2, p2: 0 |
|---|
| 322 | [flow, internal] on_battery_mount!, p1: -2, p2: 0 |
|---|
| 323 | [flow, internal] sleep off!!! |
|---|
| 324 | [flow, main] end flow_process_event() |
|---|
| 325 | |
|---|
| 326 | [flow, main, clock] finish!! |
|---|
| 327 | [mybook] on_battery_mount!, p1: 0, p2: 0 |
|---|
| 328 | <kernel : dcc> dcc_loop_timer_worker(): ### (0) (0) (0) (8) ### |
|---|
| 329 | <kernel : dcc> dcc_loop_timer_worker(): ### (0) (1) (0) ### |
|---|
| 330 | |
|---|
| 331 | [flow, internal] on_battery_mount!, p1: 0, p2: 0 |
|---|
| 332 | [flow, internal] on_battery_mount!, p1: 0, p2: 0 |
|---|
| 333 | [flow, internal] change battery level: 0 |
|---|
| 334 | <start>(msg)(0x0000A121) |
|---|
| 335 | <kernel : dcc> change_to_low_clock(): ## to check again!! 11## |
|---|
| 336 | <kernel : dcc> write_proc_clock(): Recieve value 12 from app |
|---|
| 337 | Change freq level 0 range |
|---|
| 338 | <start>(msg)(0x0000A121) |
|---|
| 339 | Change freq level 8 range |
|---|
| 340 | <kernel : dcc> force_high_clock(): |
|---|
| 341 | ## Silence Clock change sleep count=3 ## |
|---|
| 342 | <kernel : dcc> change_to_low_clock(): ## Current epd mode is not sleep state, so try to check again!!# |
|---|
| 343 | <kernel : dcc> write_proc_clock(): Recieve value 12 from app |
|---|
| 344 | Change freq level 0 range |
|---|
| 345 | <kernel : dcc> dcc_loop_timer_worker(): ### (0) (0) (4) (0) ### |
|---|
| 346 | <kernel : dcc> dcc_loop_timer_worker(): ### (0) (2) (0) ### |
|---|
| 347 | |
|---|
| 348 | <start>(msg)(0x0000A121) |
|---|
| 349 | Change freq level 8 range |
|---|
| 350 | <kernel : dcc> force_high_clock(): |
|---|
| 351 | ## Silence Clock change sleep count=9 ## |
|---|
| 352 | <kernel : dcc> change_to_low_clock(): ## Current epd mode is not sleep state, so try to check again!!# |
|---|
| 353 | <kernel : dcc> write_proc_clock(): Recieve value 12 from app |
|---|
| 354 | Change freq level 0 range |
|---|
| 355 | <kernel : dcc> dcc_loop_timer_worker(): ### (0) (0) (13) (0) ### |
|---|
| 356 | <kernel : dcc> dcc_loop_timer_worker(): ### (0) (2) (0) ### |
|---|
| 357 | |
|---|
| 358 | <start>(msg)(0x0000A121) |
|---|
| 359 | Change freq level 8 range |
|---|
| 360 | <kernel : dcc> force_high_clock(): |
|---|
| 361 | ## Silence Clock change sleep count=15 ## |
|---|
| 362 | <kernel : dcc> change_to_low_clock(): ## Current epd mode is not sleep state, so try to check again!!# |
|---|
| 363 | <kernel : dcc> write_proc_clock(): Recieve value 12 from app |
|---|
| 364 | Change freq level 0 range |
|---|
| 365 | <start>(msg)(0x0000A121) |
|---|
| 366 | Change freq level 8 range |
|---|
| 367 | <kernel : dcc> force_high_clock(): |
|---|
| 368 | ## Silence Clock change sleep count=21 ## |
|---|
| 369 | <kernel : dcc> dcc_loop_timer_worker(): ### (0) (0) (21) (8) ### |
|---|
| 370 | <kernel : dcc> dcc_loop_timer_worker(): ### (0) (1) (0) ### |
|---|
| 371 | |
|---|
| 372 | <kernel : dcc> change_to_low_clock(): ## Current epd mode is not sleep state, so try to check again!!# |
|---|
| 373 | <kernel : dcc> write_proc_clock(): Recieve value 12 from app |
|---|
| 374 | Change freq level 0 range |
|---|
| 375 | <start>(msg)(0x0000A121) |
|---|
| 376 | Change freq level 8 range |
|---|
| 377 | <kernel : dcc> force_high_clock(): |
|---|
| 378 | ## Silence Clock change sleep count=27 ## |
|---|
| 379 | <kernel : dcc> change_to_low_clock(): ## Current epd mode is not sleep state, so try to check again!!# |
|---|
| 380 | <kernel : dcc> write_proc_clock(): Recieve value 12 from app |
|---|
| 381 | Change freq level 0 range |
|---|
| 382 | <kernel : dcc> dcc_loop_timer_worker(): ### (0) (0) (28) (0) ### |
|---|
| 383 | <kernel : dcc> dcc_loop_timer_worker(): ### (0) (2) (0) ### |
|---|
| 384 | |
|---|
